The product you were looking for no longer exists! Here are products you may be interested in from the same category.
High-Quality Construction
Also Fits 1939-1948 Ford & Mercury Station Wagons And 1932-1934 Pickup
Single Knob Included - Two Required Per Vehicle
This knob holds the swing arms in place when the windshield is open…
The piece that the windshield hinges on. Fits 1930-31's. Mounts to the top of the windshield opening. ALUMINUM, 45-3/8" long…
Also Fits 1932 Passenger Car
Assists in holding the windshield securely in open or closed position.
…
Oval head 5/16" x 18 coarse thread screws.
Attaches the lower windshield stanchions to the body on open cars.
Some later cars may have also used coarse-threaded screws.
…
Steel cup shaped socket that is welded into the windshield stanchion where the windshield frame cone rests and pivots. The frame cone rides in this cup. Used on 1928-31 Roadsters, Roadster Pickup, and Phaeton. If you are ordering new…
Product Overview Die stamped with high quality stainless steel.…
Use with # A45475S bolt set. Also 1932 Passenger.
…
This has the proper taper for a correct fit. It goes between the windshield frame and windshield stanchions at the pivot point, and allows the windshield to tilt.
…
The clamp is screwed onto the end of the frame to hold the glass in place. This stamped steel cap was used on 1926-27 Roadster and Touring cars. U.S.A.
…
1922-25 requires (2), 1926-27 requires (4).
…
This has the proper taper for a correct fit. It goes between the windshield frame and windshield stanchions at the pivot point, and allows the windshield to tilt.
…
The rubber gasket for the bottom and sides of the closed car steel windshield frame. Put the bottom in first, but don't cut it. Wait till the next day to finish the job, as this lets the rubber shrink so the corners will be tight. 8' long…
Oval head 5/16" x 24 fine thread screws.
Attaches the lower windshield stanchions to the body on open cars.
Some earlier cars may have also used fine-threaded screws.
…
Seals the frame to the body.
Enough to do both sides and the bottom of the frame.
…
Rubber seals that seal the sides and bottom of the 1930-31 Roadster, Roadster Pickup, and Phaeton windshield frame. Uses a 1" x 46" long "T" shaped piece in the bottom of the windshield frame and a 1/2" x 32" "T" shaped piece that inserts…
Must re-use your original hinge-to-windshield frame bracket ( not currently being reproduced ).
…
Model A Ford Windshield Finger Pull Screw Set - 2 Pieces
…
You will need a total of eight of these. 4 hold the bottom of the lower windshield frame to the cowl, and 4 hold the upper frame glass clamps. A set consists of 1 screw and 1 sleeve nut.
…
Stainless steel stanchions for the 1930-31 Deluxe Roadster and Deluxe Phaeton. Complete with sockets and the post liner. These only fit the deluxe, not the standard. Stanchions are polished. Drivers side stanchion is drilled/tapped for the…
This is the steel garnish molding that screws to the windshield posts of closed cars. Goes on left and right of windshield opening. Sold in pairs only. USAFits 1928-29 Coupes and Tudor Sedan.…
Includes stud and cone nuts. 3/8" x 24 thread on both ends. 1 set required for 1922-25, 2 sets required for 1926-27.
…
These are used to hold the frame together.
…
These go between the stanchion and the wingnut.
…
Lower windshield stanchions for the windshield in plain steel. Used on all 1930-31 Roadsters, Roadster Pickup, and Phaeton.They include the fine threaded stud that secures the upper stanchion to it.Sold in pairs only. U.S.A.
…
This does not include interior vertical division bar.
…
These are used to hold the frame together.
…
Fits into lower part of stanchion.
…
An exact copy of the windshield bracket that was used on all of the closed cars. The swing arms mounted to this bracket, rivets included. U.S.A.Fits all 1930-31's except slant windshield models.…
These hold the frame together.
…
With mounting rivets. Will require two (2) per car.
USA made.
…
#6061 aluminum alloy closed car windshield frames. Close duplicates of originals! Comes complete with frame gasket, swing arm brackets and the mounting hinge. USAFits all 1930-31's closed body styles except Slant Windshield 31's.…
Attaches to outside of windshield frame where both sides join. Covers the gaps where upper & lower frame halves meet. Also Pickup Truck.
Polished and USA made.
…
Also Convertible Sedan
Small, rounded edge of seal goes toward outside. Also Convertible Sedan.
…
New hardware available for your 1957-1959 Ford hide away hardtop and convertible coupe.…
5/16-18 brass acorn nuts used with our T-7836-ST studs to attach firewall and dash brackets on early T firewalls. U.S.A.…
Stamped from solid Brass & highly polished.
…